無錫倉儲地坪價格是多少 400-0709-910(請撥打400-0709-910電話，永堅地坪公司)
耐油性：耐磨地面本身不具備耐油性。如果要達到良好的抗?jié)B耐油性能，可便用HOPER液態硬化劑、混凝土密封固化劑從而使耐磨地面表層有更佳的致密性、達到良好的抗?jié)B性，并可以提高地面的耐磨強度和光澤度。
抗腐蝕性 骨料標準鹽蝕試驗.，42 d自然電信恒為正、穩定值+0.5㎜(S.C.E)，**值+120MV(S.C.E)水泥試體，5%NACI
溶液浸泡，2年零3個月無銹斑。
地坪養護：
耐磨地坪完工后（視天氣溫度情況），用水加PVC薄膜或?qū)Ｓ灭B(yǎng)護劑，涂敷耐磨地坪表面進行養護，防止其表面水分激烈蒸發，保障耐磨地坪強度的穩定，養護時間為七天。
施工方案：
一、初次刮除浮漿
混凝土在澆注一定時間后（具體時間因氣候定）用橡皮推刀刮除水，浮漿
耐磨地坪施工工序：
**次提漿
**次撒布
整平提漿
第二次撒布材料
二次撒布材料提漿
第三次撒布材料
在氣溫偏高的情況下，因混凝土凝固較快也可分二次，完成撒布材料
收光作業
耐磨地坪是在基層混凝土初凝階段，將耐磨材料均勻撒布在混凝土表面，經專業機械施工，從而使其與混凝土地面形成一個整體，完工后的地坪具有**致密性、加倍提高地坪耐磨性、抗壓性、及耐沖擊性，使用壽命長。
（一）、耐磨材料概述:
耐磨材料是由骨料、波蘭特種水泥及顏料和外劑等經合理級配生產的。骨料為砂狀，是天然礦石成分，硬度在莫氏8度以上，平均粒徑為1.5mm，占總量的60%；膠結物經過處理的高標號特種水泥，基本色調有原色、灰色、鐵紅色、綠色等。
（二）、 施工現場，具備以下條件：
1、施工現場的照明要充分（滿足夜間施工需求）；
2、業主或總包方需在施工現場提供堆放材料及機器設備的倉庫；
3、澆筑混凝土?xí)r，每天澆筑量800-1000m2，金剛砂施工人員6-8人，機器7-9臺；
4、為避免耐磨地面施工播撒材料時污染墻面或柱面,正在裝飾的墻面、柱面，需預留距地面約1.5米左右的高度,待耐磨地面完工后再繼續裝飾；如已經裝飾好的在約1.5米左右的高度間用塑料薄膜遮蓋保護；
5、如有預埋管道及機器接口，需預先做好準備：
6、業主或總包方應提前**施工現場中的雜物，確保能如期施工；
7、耐磨地坪施工時，現場班組不得交叉作業。
8、抹光完成后的地面，必須進行養護，用**專用的養護臘進行養護。
（三）、耐磨地坪施工工藝
耐磨材料撒布的時間隨氣候、濕度、混凝土配合比及外加劑品種性能等因素而變化。撒布過早會使耐磨材料沉入混凝土中而失去效果；撒布太晚混凝土已凝固，會失去粘結力，使耐磨材料無法與其結合而造成剝離�；炷翝仓�3-5小時，腳踩約下陷5mm，視表面無泌水且成初凝狀態則進行耐磨材料工序：
1、每平方米耐磨材料撒布量不低于5Kg/m2；
2、墻、柱、門和模板等邊線處水分消失較快，宜優先撒布施工，以防因失水而降低效果；
3、首先，給拋光機裝上圓盤，整體打磨混凝土表面，從周邊逐漸向內收抹，起到提漿作用；
4、**次將2/3的**耐磨材料均勻撒布在混凝土表面，材料吸收混凝土中的水分，顏色變深后，即可開始**次抹平，工具采用抹光機（裝圓盤），時間應撐控好，應注意不要搓抹過度；
5、緊接著，將余下1/3的**耐磨材料均勻撒布混凝土表面，施工方向與**次垂直，隨后進行第二次抹平工作；抹光作業時應縱橫交錯進行，均勻有序，防止材料聚集。
6、**，必須用抹光機（刀片）完成進行收光，收到光亮為止。注意隨著混凝土凝固時應調整刀片傾斜角度，此時地面已有一定的硬度，不易被破壞；
7、邊角處需用人工抹光，收邊；
8、養護：抹光完成后的地面，必須進行養護。應在地坪完成6-12小時內用**專用養護臘進行養護。
9、為防止不規則龜裂，耐磨地坪完工2天后應切切割縫，切割縫方塊為4-6m (一般根據車間梁柱距離而定)，為使切割縫整齊順直，應先統一彈線，切割深度應是地坪厚度的1/3，切割縫由土建完成，填縫材料用彈性膠或彈性樹脂。
（四）、 成品保護：后續各工種、工序應妥善保護完工地面
1、嚴禁在成品地面上拌和材料污染到地面，影響質量；
2、完工后的金剛砂地面需灑水養護一周；
3、水電安裝施工應嚴禁鐵架鐵梯、鋼管材料、風管材料等，破壞成品地面，尤其地面仍處養護期內時；
4、梁柱底板粉刷涂料時，應鋪放遮蓋物，嚴禁到處灑落；
Oil resistance: Wearresisting itself does not have oil resistance. If you want to achieve good impermeability oil resistance, can you use HOPER liquid hardener, concrete sealer so that the wear surface of the ground have a better density, to achieve good impermeability, and abrasion resistance can be improved ground and gloss.
Corrosion aggregate standard salt corrosion test., 42 d of natural telecommunications always positive, stable value + 0.5 mm (SCE), the maximum value of + 120MV (SCE) cement test specimen, 5% NACI
Solution soak, 2 years and 3 months, no rust.
Floor conservation:
Wear-resistant floor after completion (depending on weather temperatures), water and PVC film or special curing agent, coating wear-resistant floor surface maintenance, prevent rapid evaporation of surface moisture, protect the stability of wear-resistant floor strength, curing time seven days.
Construction program:
First, the initial curettage laitance
Pouring concrete at a certain time (the time due to climate may be) scraping with a rubber knife to push the water, floating pulp
Wear-resistant floor construction process:
The first mention pulp
First spreader
Leveling mention pulp
Second spreading material
Secondary mention slurry spreading material
Third spreading material
In the case of high temperatures, because the rapid solidification of concrete can be divided into secondary, complete spreading material
Received light work
Wear-resistant floor at the grassroots level concrete initial setting stage, the wear-resistant material evenly spreading the concrete surface, the professional mechanical construction, making it the concrete floor form a whole, after the completion of an efficient dense floor, doubling to Ping wear resistance, resistance to stress, and impact resistance, and long service life.
(A), wear-resistant material Overview:
Wear-resistant material is made of aggregate, cement and pigments and Polish special outside agent, after reasonable grading of production. Aggregate is sand-like, natural mineral ingredients, Mohs hardness of more than 8 degrees, the average particle diameter of 1.5mm, accounting for 60% of the total; cement processing through high-grade special cement, basic colors have color, gray, iron red, green and so on.
(B), the construction site, with the following conditions:
1, the construction site lighting should be sufficient (to meet the construction needs of the night);
2, the owner or general contractor must provide stacking materials and equipment warehouse at the construction site;
3, when the pouring of concrete pouring daily volume 800-1000m2, construction workers Emery 6-8, 7-9 sets of machines;
4, in order to avoid the wear-resistant surface construction material contamination spreading or cylindrical walls being decorated walls, cylindrical, to be reserved from the ground about 1.5 meters height, wear-resistant surface to be completed before proceeding decoration; as It has a good decoration at a height of about 1.5 meters between the plastic film covering protection;
5, if the embedded pipes and machine interface, you need to prepare in advance:
6, the owner or the total package in advance to clear the construction site of debris, to ensure the construction schedule;
7, wear-resistant floor construction, site work team may not cross.
8, wiping the floor after completion of the light must be conservation, conservation with special conservation of the Royal Prince.
(Iii), wear-resistant floor construction process
Wear-resistant materials strewn time with climate, humidity, concrete mix and admixtures performance factors. Spreading premature wear-resistant materials will lose the effect of sinking concrete; concrete has solidified spreading too late, lose adhesion, abrasion-resistant material so that its binding and can not be caused by the release. 3-5 hours after the concrete pouring, foot subsidence of about 5mm, depending on the surface without bleeding into the initial setting state and wear-resistant materials is carried out the steps of:
1, per square meter of wear-resistant material spreading of not less than 5Kg / m2;
2, sideline water walls, columns, doors and templates disappear quickly, should give priority to spreading construction, to prevent water loss and reducing effect;
3, first, to the polishing machine mounted on the disc, overall polished concrete surface, wipe gradually inward from the periphery, the role played mention pulp;
4, the first two-thirds of the Royal resistant materials evenly spreading the concrete surface, the concrete material absorbs moisture, after darken, you can start the first smooth, tool use trowel (loaded disk ), the time should hold good control, you should be careful not to rub the wipe over;
5, followed by the Royal resistant materials remaining 1/3 evenly spreading the concrete surface, construction and the first vertical direction, followed by a second smooth work; trowel work should be criss-crossing, uniform and orderly, prevent material accumulation.
6. Finally, you must use the trowel (blade) completion of received light, bright received so far. Note that when the concrete has set as adjust blade angle, this time the ground has a certain hardness, not easy to be destroyed;
7, the corners need to use artificial trowel, income side;
8, conservation: ground trowel after completion, must be conserved. Floor should be completed within 6-12 hours conservation with special conservation of the Royal Prince.
9, in order to prevent irregular cracks, wear-resistant floor two days after completion should honestly kerf, cutting sewing squares of 4-6m (generally based on the beams from the workshop may be), in order to cut straight seams and edges should be unified elastic line, cutting depth should be 1/3 the thickness of the floor, cut the seam is completed by the civil, caulking material elastic rubber or elastic resin.
(D), product protection: Follow all types of work, the process should be completed properly protected ground
1, is prohibited in the finished floor mixing material contamination to the ground, affecting the quality;
2, emery ground sprinkler maintenance required after the completion of the week;
3, installation of water should be prohibited formwork construction ladder, pipe materials, duct materials, sabotage finished ground, especially when the ground is still curing period;
4, floor beams when paint coatings, should placement covering forbidden spilled everywhere;
資訊來源：<聯系電話:400-0709-910>
|
您當前的位置: 首頁 > 行業資訊
