無錫工業環氧地坪價格是多少 400-0709-910(請撥打400-0709-910電話，永堅地坪公司)
專業生產金剛砂耐磨地坪一般是由冶煉的金剛砂及特殊添加劑與標準高標號水泥和其它高科技化學材料生產合成。金剛砂耐磨地坪經與新澆混凝土基面整體固化后，具有表面硬度高、密度大、耐磨、不生灰塵、不易剝離形成一密實平整、無接縫、無孔面層。金剛砂耐磨地坪耐磨性、耐沖擊性、強度是普遍混凝土(C30)地面的數倍以上，而且其堅硬、密實的表面可抵抗油脂和潤滑油。
金剛砂耐磨地坪摒棄了傳統的混凝土基層與面層分開施工的做法，從而**了因基層與面層結合不良而導致裂縫 和空鼓的質量通病，金剛砂耐磨材料簡化了工序，縮短了施工周期，節約人工費用，經濟、適用、范圍廣等優點在工廠、倉庫、跑道、 碼頭等工程中得到越來越廣泛的應用。
金剛砂耐磨地坪對找平層的要求：
金剛砂耐磨地坪對有鋼筋要求的地臺，應按設計設置鋼筋或鋪設網眼孔徑為5㎝×5㎝的鋼網，鋼筋或鋼網下面設置墊塊；
在澆注混凝土作業時，需用震動橋或水平式震動器對混凝土進行震實作業；
由于地面進行分倉作業，應在每倉邊緣架設標高鋼模或木模板，以確保表面水平度；
注要分倉按序進行，以保證整體地面水平硬化層的機器作業；
金剛砂耐磨地坪工前應將所需施工地面均勻淋灑水泥油，以防止找平層起殼；
使用較重的鋼制長輥對混凝土進行輾壓，使地面達到初平，并用膠管去除多余泌水后，便可交予我方進行硬化劑施工。 金硅地生成的混凝土液態硬化劑是通過充分滲透，其**成分能迅速地與混凝土中的游離鈣發生化學反應，增加結構的致密性，使得混凝土表層形成一個堅如磬石的堅固實體，極大地提高混凝土結構表層的強度和耐磨性，從而得到**封閉、堅固、耐磨、不起塵、抗水和大多數工業化學品侵蝕的表面。熟化封堵，不會像表面涂層隨著使用而磨損，本品因為**地鎖住孔隙，會使混凝土變得愈來愈硬，封堵性愈來愈好。
金硅地混凝土液體硬化劑使用方法
1.在正式使用前，建議針對特定地面先進行現場小面積試驗，在確認使用效果和用量后再大面積使用。
（施用前請攪拌均勻）。
2.在清理干凈的混凝土表面上，噴灑或滾涂歐佳牌混凝土表面增強劑，（一般一遍即可，第二遍視**遍效果而定,時間在**遍施工后2-12小時之間**），維持飽和濕潤狀態 10-20分鐘，以利更多**成份進入混凝土內部。Specializing in the production carborundum wearable Floor is generally made of carborundum smelting and special additives and standard grade cement and other high-tech production of synthetic chemical materials. Emery wear floor after pouring the concrete surface with the new overall curing, high surface hardness, density, wearable, not raw dirt, easy to peel the formation of a dense smooth, seamless, nonporous surface. Carborundum wearable Floor abrasion resistance, impact resistance, strength is several times more than common concrete (C30) ground, and its hard, dense surface that is resistant grease and lubricants.
Carborundum wearable Floor abandon the traditional concrete base and surface construction of separate practices, thereby eliminating the grassroots and the surface layer due to bad combination resulting in cracks and hollowing quality defects, Emery wear material simplify the process and shorten the construction cycle, saving labor costs, economical, practical, wide range of advantages to be more widely used in factories, warehouses, runways, terminals and other projects.
Carborundum wearable Floor screed on request:
Carborundum wearable Floor reinforcement required to have ground units, according to the design or paved with reinforced mesh aperture of 5 cm × 5 cm of steel mesh, steel or steel mesh pad set below;
When pouring concrete work, bridge or horizontal vibration required Vibrators real shock for concrete operations;
Since the ground operation sub-positions, should erect steel or wooden template level positions in each edge, to ensure that the level of the surface;
Note To binned performed sequentially, in order to ensure that the machine work hardened layer overall level of the ground;
Carborundum wearable Floor ground workers should be required before construction even showered cement oil to prevent screed from the shell;
After using heavier steel rolling long roll of concrete, so that the ground level reached at the beginning, and with a hose to remove excess bleeding, can be handed over to our side hardener construction. Gold silicon to generate a liquid concrete hardener is through the full penetration, the active ingredient can occur rapidly with concrete free calcium chemical reaction, increasing the density of the structure, so that the concrete surface to form a hard as chime stone strong entity, pole the surface of the concrete structure greatly improves strength and wear resistance, resulting in permanent closure, strong, wear-resistant, can not afford to dust, anti-water and most industrial chemicals erosion surface. Maturation block, not as a surface coating with use and wear, this product permanently locked because the pores will become increasingly hard concrete, sealing of getting better and better.
Gold silicon liquid hardener to the concrete method
1. Before the official use, it is recommended to test a small area site-specific ground, confirming the use of effects and dosage before large-scale use.
(Please stir before application).
2. In the clean concrete surface, spray or roller Ojai brand concrete surface enhancer (general it again, the second time, as the first pass effect may be, in the 2-12 hour period after the first pass construction among the best), to maintain the saturated wet for 10-20 minutes, in order to facilitate more effective ingredients into the concrete.
資訊來源：<聯系電話:400-0709-910>
|
您當前的位置: 首頁 > 行業資訊
