精品久久久久中文字,日韩免费看视频三区中文字幕,国产成 人亚洲91,亚洲无玛在线观看

PA6 BKV 215 000000德國(guó)朗盛Durethan 15%玻纖增強(qiáng)耐沖擊尼龍6塑料（18024445500）

PA 6-Copolymer, 15 % glass fibers, injection molding, improved impact strength



ISO Shortname: ISO 1874-PA 6/66HI, GR, 14-040, GF15

Property Test Condition Unit Standard guide value
d.a.m. cond.
Rheological properties
C Molding shrinkage, parallel 60x60x2; 280 °C / MT 80 °C; 600 bar % ISO 294-4 0.59　
C Molding shrinkage, transverse 60x60x2; 280 °C / MT 80 °C; 600 bar % ISO 294-4 0.61　
Post- shrinkage, parallel 60x60x2; 120 °C; 4 h % ISO 294-4 0.14　
Post- shrinkage, transverse 60x60x2; 120 °C; 4 h % ISO 294-4 0.15　

Mechanical properties (23 °C/50 % r. h.)
C Tensile modulus 1 mm/min MPa ISO 527-1,-2 4500 2400
C Tensile Stress at break 5 mm/min MPa ISO 527-1,-2 85 55
C Tensile Strain at break 5 mm/min % ISO 527-1,-2 4.5 15
C Charpy impact strength 23 °C kJ/m² ISO 179-1eU 70 80
C Charpy impact strength -30 °C kJ/m² ISO 179-1eU 80 75
C Charpy notched impact strength 23 °C kJ/m² ISO 179-1eA 20 35
C Charpy notched impact strength -30 °C kJ/m² ISO 179-1eA 12 12
Izod notched impact strength 23 °C kJ/m² ISO 180-1A 18 30
Izod notched impact strength -30 °C kJ/m² ISO 180-1A 10 10
Flexural modulus 2 mm/min MPa ISO 178-A 4000 2200
Flexural strength 2 mm/min MPa ISO 178-A 130 80
Flexural strain at flexural strength 2 mm/min % ISO 178-A 5.0 7.0
Flexural stress at 3.5 % strain 2 mm/min MPa ISO 178-A 125 60
C Puncture maximum force 23 °C N ISO 6603-2 1003　
C Puncture maximum force -30 °C N ISO 6603-2 650　
C Puncture energy 23 °C J ISO 6603-2 13 32
C Puncture energy -30 °C J ISO 6603-2 4.8　
Ball indentation hardness　N/mm² ISO 2039-1 110 55

Thermal properties
C Melting temperature 10 °C/min °C ISO 11357-1,-3 214　
C Temperature of deflection under load 1.80 MPa °C ISO 75-1,-2 175　
C Temperature of deflection under load 0.45 MPa °C ISO 75-1,-2 205　
C Temperature of deflection under load 8.00 MPa °C ISO 75-1,-2 60　
Vicat softening temperature 50 N; 120 °C/h °C ISO 306 200　
C Coefficient of linear thermal expansion, parallel 23 to 55 °C 10-4/K ISO 11359-1,-2 0.4　
C Coefficient of linear thermal expansion, transverse 23 to 55 °C 10-4/K ISO 11359-1,-2 1.5　
C Burning behavior UL 94 (1.6 mm) 1.6 mm Class UL 94 HB　
Burning behavior UL 94 3.2 mm Class UL 94 HB　
C Oxygen index Method A % ISO 4589-2 22　
Glow wire test (GWFI) 2.0 mm °C IEC 60695-2-12 650　
Burning behavior US-FMVSS302　 ISO 3795 passed　
C Vicat softening temperature 50 N; 50 °C/h °C ISO 306 200　

Electrical properties (23 °C/50 % r. h.)
C Relative permittivity 100 Hz - IEC 60250 3.5 10
C Relative permittivity 1 MHz - IEC 60250 3.2 3.7
C Dissipation factor 100 Hz 10-4 IEC 60250 60 1500
C Dissipation factor 1 MHz 10-4 IEC 60250 150 800
C Volume resistivity　Ohm·m IEC 60093 1E11 1E10
C Surface resistivity　Ohm IEC 60093 1E15 1E13
C Electric strength 1 mm kV/mm IEC 60243-1 43 43
C Comparative tracking index CTI Solution A V IEC 60112 600　

Other properties (23 °C)
C Water absorption (Saturation value) Water at 23 °C % ISO 62 7.0　
C Water absorption (Equilibrium value) 23 °C; 50 % RH % ISO 62 2.0　
C Density　kg/m³ ISO 1183 1180　
Bulk density　kg/m³ ISO 60 600　

Processing conditions for test specimens
C Injection molding-Melt temperature　°C ISO 294 280　
C Injection molding-Mold temperature　°C ISO 294 80　

Processing recommendations
Drying temperature dry air dryer　°C - 80　
Drying time dry air dryer　h - 2-6　
Residual moisture content　% Acc. to Karl Fischer　0.03-0.12　
Melt temperature (Tmin - Tmax)　°C - 260-290　
Mold temperature　°C - 80-100　

C These property characteristics are taken from the CAMPUS plastics data bank and are based on the international catalogue of basic data for plastics according to ISO 10350.