精品久久久久中文字,日韩免费看视频三区中文字幕,国产成 人亚洲91,亚洲无玛在线观看

PA6 BKV 55 TPX 900116德國朗盛Durethan 55%玻纖增強熱老化穩定流動性改進尼龍6塑料（18024445500）

PA 6, 55 % glass fibers, injection molding, improved flowability, heat-aging stabilized



ISO Shortname: ISO1874: PA6, GHR, 10-190, GF55

Property Test Condition Unit Standard guide value
d.a.m. cond.
Rheological properties
C Molding shrinkage, parallel 60x60x2; 280 °C / MT 80 °C; 600 bar % ISO 294-4 0.2　
C Molding shrinkage, transverse 60x60x2; 280 °C / MT 80 °C; 600 bar % ISO 294-4 0.5　
Post- shrinkage, parallel 60x60x2; 120 °C; 4 h % ISO 294-4 0.1　
Post- shrinkage, transverse 60x60x2; 120 °C; 4 h % ISO 294-4 0.1　

Mechanical properties (23 °C/50 % r. h.)
C Tensile modulus 1 mm/min MPa ISO 527-1,-2 17300 10500
C Tensile Stress at break 5 mm/min MPa ISO 527-1,-2 215 140
C Tensile Strain at break 5 mm/min % ISO 527-1,-2 2.5 3.5
C Charpy impact strength 23 °C kJ/m² ISO 179-1eU 90 85
C Charpy notched impact strength 23 °C kJ/m² ISO 179-1eA 15 20
Izod impact strength 23 °C kJ/m² ISO 180-1U 90 85
Izod notched impact strength 23 °C kJ/m² ISO 180-1A 15 20
Izod notched impact strength -30 °C kJ/m² ISO 180-1A 15 20
Flexural modulus 2 mm/min MPa ISO 178-A 16500 11000
Flexural strength 2 mm/min MPa ISO 178-A 330 210
Flexural strain at flexural strength 2 mm/min % ISO 178-A 3 3.5
Flexural stress at 3.5 % strain 2 mm/min MPa ISO 178-A　210

Thermal properties
C Melting temperature 10 °C/min °C ISO 11357-1,-3 221　
C Temperature of deflection under load 1.80 MPa °C ISO 75-1,-2 208　
C Temperature of deflection under load 0.45 MPa °C ISO 75-1,-2 218　
C Coefficient of linear thermal expansion, parallel 23 to 55 °C 10-4/K ISO 11359-1,-2 0.12　
C Coefficient of linear thermal expansion, transverse 23 to 55 °C 10-4/K ISO 11359-1,-2 0.9　

Other properties (23 °C)
C Density　kg/m³ ISO 1183 1620　

Processing conditions for test specimens
C Injection molding-Melt temperature　°C ISO 294 280　
C Injection molding-Mold temperature　°C ISO 294 80　

Processing recommendations
Drying temperature dry air dryer　°C - 80　
Drying time dry air dryer　h - 2-6　
Residual moisture content　% Acc. to Karl Fischer　0.03-0.12　
Melt temperature (Tmin - Tmax)　°C - 270-290　
Mold temperature　°C - 80-120　

C These property characteristics are taken from the CAMPUS plastics data bank and are based on the international catalogue of basic data for plastics according to ISO 10350.